Replacing the gear on your Magic Bullet can seem daunting, but it’s not that hard. In this post, we’ll walk you through the process step-by-step on how to replace magic bullet gear. So whether your blade needs sharpening or you need a new one, read on for tips on how to get the job done.
One of the key reasons it’s important to replace magic bullet gear is that a dull blade can make it more difficult to create smooth, even blends, but it can also be dangerous. Conversely, a sharp blade is essential for creating the best results with your Magic Bullet.
If you’re noticing that your blends aren’t as smooth as they used to be, or if you’ve been using your Magic Bullet for a while and the blades seem to be getting dull, it’s time to replace the gear. Luckily, this process is pretty simple and can be done in just a few minutes.
Summary: Replacing the gear in a Magic Bullet blender is a relatively easy and straightforward process. It involves carefully taking apart the base of the blender, removing the old gear, cleaning off any old residue from the shaft, and then replacing it with a new gear that fits snugly against the shaft. Finally, you will reassemble the blender, which will be ready for use.
Required Materials
- Replacement gear for the Magic Bullet
- Phillips screwdriver
- Flathead screwdriver
- Pliers
- Safety goggles
How to Replace Magic Bullet Gear Step by Step Guide
Step 1: Unplug the Power Cord
Unplug your Magic Bullet blender. Wear safety goggles for this step because the blades will be exposed and jump out at you if they’re not fully engaged in their housing (remove power cord from outlet first). To remove the power cord safely, hold it with one hand and use the other hand to pull the plug out of the outlet.
Step 2: Remove Jar Lid, Blade & Gear
Remove the blade, rubber gasket, and inner lid from the jar. Use a flathead screwdriver to remove the metal ring that holds them in place and then slide them out. Next, remove the two screws that hold the blade inside the jar.
If the screws are difficult to remove, you can try using a Phillips screwdriver or a pair of pliers. If they still don’t come out, you may need a hacksaw to cut them off. Just be careful not to damage the blade or the gear while doing this. If you need to use a hacksaw to cut the screws, be very careful not to damage the blade or gear while doing this. Once the screws are cut, use a Phillips screwdriver or a pair of pliers to remove them.
Step 3: Remove Broken Gear
The gear will be visible once you’ve removed the lid and screw; slide it out with your fingers. If it doesn’t budge, use an adjustable wrench to loosen it up (this is only necessary if there is no visible way to remove the gear). If it still doesn’t budge, try using a pair of pliers on the metal ring or the edge of the jar to loosen it. If this still doesn’t work, try using a hacksaw to cut through it (again, be careful not to damage the blade).
If you can’t remove the broken gear, you may need a hacksaw to cut it off. Just be careful not to damage the blade or the gear while doing this. But firstly, identify the part is broken or not; the gear is usually located at the bottom of the jar, and it’s the part that rotates to blend the contents. If it’s broken, you’ll need to remove it and replace it with a new one.
Step 4: Unscrew & Remove the Base
Remove the black base by unscrewing it with a Phillips-head screwdriver. Note how this process came apart – there should be two screws on top and two underneath (also note how the inner workings fit together).
Step 5: Remove the Blade and Gear Assembly
Remove the blade and gear assembly from inside the base of your Magic Bullet. The gear should slide right out (you might need to use a flathead screwdriver if it’s stuck). Please pay attention to how this came apart, as you’ll need to put it back together later.
Step 6: Remove the Blade from The Gear
Remove the blade from its gear. You may need a pair of pliers if the blade is stuck to the gear for this step. Keep in mind how this came apart so you can put it back together later on when you replace your Magic Bullet gear!
Step 7: Insert Replacement Gear
Insert the new Gear into place and replace the rubber gasket, screw, and blade. Then plug in your blender and enjoy how smoothly it blends again! Replacing Magi Bulletc gear is a straightforward process and can often be done less than 10 minutes.
Step 8: Replace Blade & Gear Assembly
Replace the blade and gear assembly into the base. Make sure that the holes line up how they came apart. Use a Phillips-head screwdriver to tighten two screws on top of the base and then tighten two screws underneath.
Step 9: Replace Lid, Gasket & Metal Ring
Replace the metal ring, gasket, and lid that held the blade in place. Again, please pay attention to how these came apart so you can replace them how they originally were.
Step 10: Replace Base
Put the base back onto your Magic Bullet by sliding it on how it came off (you may need somebody to hold the jar while you screw the base on). Then line up how the base came apart with the two screws above and underneath. Finally, plug in your Magic Bullet blender.
Congratulations! You have successfully replaced your Magic Bullet’s gear so you can get back to making smoothies again!
The other thing you should consider when replacing the gear in your Magic Bullet is how to put it back together again. Putting it all back together is very similar to how it came apart, so take your time and make sure everything is in the correct place before tightening any screws. If you want to know more about how to replace magic bullet gear, keep reading.
Why Is My Magic Bullet Not Blending?
If your Magic Bullet isn’t blending like it used to, it might be because the blades are clogged. The typical cause of a clogged blade is dried-out or caked-on food deposits leftover after chopping vegetables at high speed for 10 minutes. As the food particles build up, they create a glue-like consistency that causes your blender’s blades to clog over time.
To fix this, you can either try to clean the blades yourself or change the gears on the machine. If you choose to try to clean the blades yourself, be sure to unplug the machine and wait for it to cool down before removing the cover. There are three screws on the bottom of the cover that needs to be removed before taking it off.
Once the screws are removed, you can pull the cover off. The gears are located in the middle of the machine. You will need to loosen the two screws that hold them in place to remove them. Once they are loose, you can pull the gears out and replace them with new ones. Again, be sure to tighten the screws before putting the cover back on.
Can You Sharpen Magic Bullet Blades?
There are three screws on the bottom of the cover that needs to be removed. Once the screws are removed, you can pull the cover off. The gears are located in the middle of the machine. You will need to loosen the two screws that hold them in place to remove them. Once they are loose, you can pull the gears out and replace them with new ones. Be sure to tighten the screws before putting them back on.
If your head is shaking uncontrollably because your blender’s blades have seen better days, here’s how to get your blender back up and running like brand new again!
The typical cause of a clogged blade is dried-out or caked-on food deposits leftover after chopping vegetables at high speed for 10 minutes. As the food particles build up, they create a glue-like consistency that causes your blender’s blades to clog over time. Keep reading for more information about how to replace magic bullet gear.
How Do You Change the Gears on A Magic Bullet?
To change the gears on a Magic Bullet, you will need to remove the cover. There are three screws on the bottom of the cover that needs to be removed. Once the screws are removed, you can pull the cover off. The gears are located in the middle of the machine. You will need to loosen the two screws that hold them in place to remove them. Once they are loose, you can pull the gears out and replace them with new ones. Be sure to tighten the screws before putting the cover back on.
How Do You Change Plastic Gear in Magic Bullet?
To change the plastic gear in a Magic Bullet, you will need to remove the cover. There are three screws on the bottom of the cover that needs to be removed. Once the screws are removed, you can pull the cover off.
The gears are located in the middle of the machine. You will need to loosen the two screws that hold them in place to remove them. Once they are loose, you can pull the gears out and replace them with new ones. Be sure to tighten the screws before putting the cover back on.
How do you disassemble a Magic Bullet?
To disassemble a Magic Bullet, you will need to remove the cover. There are three screws on the bottom of the cover that needs to be removed. Once the screws are removed, you can pull the cover off. The gears are located in the middle of the machine. You will need to loosen the two screws that hold them in place to remove them. Once they are loose, you can pull the gears out and replace them with new ones. Be sure to tighten the screws before putting the cover back on.
Conclusion
We’ve got you covered if you’re looking for a one-stop-shop to replace all of your magic bullet gear. Our team has the experience and expertise to help you find the perfect replacement for your old gear and get you up and running with the new tools in no time. Contact us today to learn more about our products and services! Thanks for reading our post about how to replace magic bullet gear.
You can check it out to Use the Ninja Auto IQ Blender
