Ninja blenders are known for their power and durability, but they can also be loud. If so, this blog post is for you! In today’s post, we will be discussing how to make ninja blender quieter. Keep reading for tips and tricks that will help reduce the sound level of your blender. Let’s get started!
There are a few reasons why making ninja blender quieter is important. First and foremost, no one wants a loud blender interrupting their peace and quiet. Additionally, a quieter blender is less likely to wake up people in the house or bother those trying to work or study. Finally, a noisy blender can be annoying and distracting, leading to decreased productivity. So keep reading if you’re looking for ways to make your ninja blender quieter!
Table of Contents
- 1 Required Materials
- 2 How to Make Ninja Blender Quieter Step by Step
- 2.1 Step 1: Clean the Blender
- 2.2 Step 2: Remove the Lid Gasket
- 2.3 Step 3: Replace the Gasket Seal
- 2.4 Step 4: Check how Cover Seals to Base
- 2.5 Step 5: Replace the Rubber Ring
- 2.6 Step 6: Remove Hair from the Blades
- 2.7 Step 7: Lubricate the Ninja Blender Base
- 2.8 Step 8: Oil the Ninja Blender Motor
- 2.9 Step 9: Replacing Motor Shaft Seal
- 2.10 Step 10: Remove & Clean Cover
- 2.11 Step 11: Reassemble & Test It Out!
- 3 How Do You Soundproof a Ninja Blender?
- 4 Frequently Asked Question
- 5 Conclusion
- Ninja blender
- Noise-canceling headphones or earplugs
- Insulation material
If you’re looking to make your ninja blender quieter, there are a few things you can do. One of the simplest methods is to use insulation material. You can find insulation material at most hardware stores. Another option is to use noise-canceling headphones or earplugs. These will help to block out the sound of the blender. Finally, if you have the time and money, you can purchase a new ninja blender designed to be quieter.
How to Make Ninja Blender Quieter Step by Step
Step 1: Clean the Blender
Clean the inside and outside of your Ninja blender. No food remains in or around the blades, base, or pitcher. Remove them from the pitcher and wash them under running water to clean the blades. Also, clean off any residue build-up on the base of your Ninja blender with a soft brush before unplugging the unit.
Step 2: Remove the Lid Gasket
Next, remove the lid gasket. This is typically a small rubber washer that fits in the top hole of your Ninja blender’s lid and should be easy to pry out with your fingers. After it pops out, you can wash and dry the gasket before replacing it in its original position.
Step 3: Replace the Gasket Seal
You can now replace the gasket seal/washer on the Ninja blender’s lid. Push into place until you hear a click. This click will let you know that the washer is completely in place and ready to go. Tip: Make sure it is dry before putting back on.
Step 4: Check how Cover Seals to Base
Use your hand to hold the lid in place while turning the Ninja blender on for 5-10 seconds; then, turn it back off and remove the cover. If there were anything loose inside the pitcher (and not attached to blades) like food or sticky liquids, it would be stuck to the bottom of the lid. If there is nothing, move to Step 5; if there is something, remove it and then re-check how the cover seals to base.
Step 5: Replace the Rubber Ring
Turn off and unplug your Ninja blender. Carefully remove the rubber ring from the threads on the blade base, being careful not to lose it down into the inner workings of your blender. Please look at how the rubber ring is placed in the order that you put it back on correctly. Then, re-install the ring, taking care to tighten it firmly.
Step 6: Remove Hair from the Blades
Please remove excess hair in your Ninja blender by removing it with a needle or crochet hook. To do this, remove the blades from the base and slide the needle or crochet hook through any spaces between blades to pick out any leftover hair strands. Clean off these strands with a paper towel.
Step 7: Lubricate the Ninja Blender Base
Dip a Q-tip in vegetable oil and use it to lubricate any areas of your Ninja blender base containing gears or other moving parts. If the pitcher is difficult to remove from the blender after implementing this solution, you can also apply some vegetable oil to its bottom.
Step 8: Oil the Ninja Blender Motor
Dip a Q-tip or toothpick in vegetable oil and apply it to your Ninja blender’s motor located under the pitcher and/or blades. Hold down the pulse button for five seconds, then release; this will spread out the oil evenly on all parts of the motor.
Step 9: Replacing Motor Shaft Seal
You can now replace the motor shaft seal by placing it on top of the blades and then pressing down firmly. You will hear a click, letting you know that it is back in place. Replacing the lid will automatically lock this into place.
Step 10: Remove & Clean Cover
This time you will need a flat head screwdriver – carefully – pry open the four small black clips on the cover (one on each corner). After removing the lid, remove and clean the gasket. Put it all back together by repeating Step 4; if there’s anything stuck to the bottom of your Ninja blender’s lid, then you should repeat this process again until the lid is clean.
Step 11: Reassemble & Test It Out!
Reassemble Your Ninja Blender Put the blender base back on, making sure that all of its pieces are properly aligned and tightened. Replace the pitcher by lining up the arrows at its base with those on the blender base. Then put your hands around both parts and slide the pitcher down. Place your thumb on the pulse button and push it in, then slide back to lock it into place.
Now that you’ve replaced all of those gaskets, cleaned everything thoroughly, and reassembled your blender as necessary, you’re ready to give it a spin. Slowly, plug the blender back in and flip the power switch to ‘On.’ Let it run on high for 30 seconds, then stop it and let it cool off before exposing your hands to the pitcher. This will allow all of its moving parts time to become lubricated by the fresh oil that you applied during this how-to.
Keep reading for more information about how to make ninja blender quieter.
How Do You Soundproof a Ninja Blender?
There are a few ways to soundproof a Ninja blender. One way is to add some insulation to the blender’s housing. You can also dampen the noise by adding some sound-absorbing material to the inside of the blender’s housing. Finally, you can place the blender in a soundproof enclosure.
If you’d like to make your Ninja blender a little quieter, follow these steps:
1. Find out how much noise your Ninja blender makes by turning it on and placing a decibel meter next to the motor housing. Write down how loud it is.
2. Add insulation to the blender’s housing with spray-on insulation foam.
3. Add some sound-absorbing material, like Dynamat or sound-deadening rubber, inside the blender’s motor housing (but don’t block the air vents).
4. If you still think it’s too loud, make a soundproof enclosure for your Ninja blender out of 3/4 inch plywood and weatherstripping.
5. If it is still too loud, you may need to use a different appliance or place the blender in another room.
If you want to know more about how to make ninja blender quieter keep reading.
You Can check it Out to Make a Blender Quieter
Frequently Asked Question
What Is the Quietest Blender?
If you are looking for a quieter blender, the Ninja may not be the best option. Some quieter blenders include the Vitamix 7500 and the Blendtec Designer Series Wildside Blender.
Why Is My Ninja Bullet so Loud?
There can be a few reasons why your Ninja Bullet is so loud. One reason may be that the blades are not tight enough, which can cause the motor to strain and make more noise. Another reason may be that there is too much noise-causing vibration. You can dampen vibration by adding some sound-absorbing material to the blender’s housing.
How Long Do Ninja Blades Last?
Ninja blades can last a long time if they’re properly taken care of. It would help if you never run the blender with an empty container, as this can cause the blades to overheat. You should also avoid putting pressure on the blade while it’s spinning by not stuffing large amounts of food into the blender at once. If you take care of your blades, they can last for many years.
Why Does My Ninja Foodi Smell Like Plastic?
There can be a few reasons why your Ninja Foodi smells like plastic. One reason may be that the smell is coming from the plastic casing on the outside of the machine. Another reason may be that the smell is coming from the container.
Finally, the smell may also be caused by the gasket, which is the rubber ring that seals the container to the machine’s base. If you’re experiencing a plastic smell from your Ninja Foodi, try cleaning these parts with a mild detergent and water. You can also try using a vinegar-based solution to clean the parts.
Which Is Quieter Nutribullet or Ninja?
If you are looking for a quieter blender, the Nutribullet may be a better option than the Ninja. The Nutribullet has fewer blades and doesn’t rely on as much power to blend, making less noise.
You can check it out to Sharpen Vitamix Blade
So, if you’re looking for a ninja blender that’s both powerful and quiet, we’ve got just the models for you. And don’t forget to check out our other top kitchen appliances – we know you’ll find the perfect fit for your needs. Thanks for reading how to make ninja blender quieter and happy blending!